Bedford CF-UK Message Board Logo [Home] [Search] [FAQ]
Bedford CF-UK Message Board > CF Questions > gearbox
[Private Message] [Register] [Profile] [Member list] [Log-in]
Who's Online:
There are 0 member(s), and 1 guest(s) online.
 
[Printable Version] [Post Reply]
Author Message
Anon
Deleted
Posts :
Location :
Status    : Offline

gearbox

I am in the process of fitting a new gearbox to my cf on the box I am taking out their is a place to connect two wires on the plate that the gear stick goes into on the new box it is blank can I just swap the plates round and I need a seal for were the speedo cable goes in any one know were I can get one thanks
Wed 25 May 2016 @ 11:11 Edit this messageQuote this messagePMQuote this message
bluebedouin
Global Moderator
Posts : 2444
Location : Northampton,England.
Status    : Offline

Could you put up a pic of the old seal?I have a box of bits & bobs that might have one in but I need to know what I'm looking for.

----------------------

Wed 25 May 2016 @ 12:38 View bluebedouin   Email bluebedouin   Edit this messageQuote this messagePMQuote this message
Anon
Deleted
Posts :
Location :
Status    : Offline

there is a picture of the seal in the file downloads group 8 at the speedometer section it a small seal with a spring over it
Thu 26 May 2016 @ 10:19 Edit this messageQuote this messagePMQuote this message
Anon
Deleted
Posts :
Location :
Status    : Offline

Cover plate.

Hi Joe,

I think you are just talking about the cover plate on the gearstick turret, if so then you can just swap them over, you must have a reverse light switch fitted to your own one, the plate is just held on by two 7/16 AF studs.

doujoy

----------------------

Thu 26 May 2016 @ 17:11 Edit this messageQuote this messagePMQuote this message
Anon
Deleted
Posts :
Location :
Status    : Offline

yes I think that's what the wires do any seals needed on the plate
Thu 26 May 2016 @ 22:15 Edit this messageQuote this messagePMQuote this message
Anon
Deleted
Posts :
Location :
Status    : Offline

yes I think that's what the wires do any seals needed on the plate
Thu 26 May 2016 @ 22:15 Edit this messageQuote this messagePMQuote this message
Anon
Deleted
Posts :
Location :
Status    : Offline

Cover plate.

Hi Joe,

There is a seal behind that gearstick turret so no need for a seal under the cover plate but before you fit the plate make sure there is plenty of grease inside the casing to keep the selector shaft and finger lubricated and keep the water out.

doujoy

----------------------

Fri 27 May 2016 @ 10:17 Edit this messageQuote this messagePMQuote this message
Anon
Deleted
Posts :
Location :
Status    : Offline

thanks doujoy know anywhere I could get the o ring seal for the speedo cable
Fri 27 May 2016 @ 11:14 Edit this messageQuote this messagePMQuote this message
Anon
Deleted
Posts :
Location :
Status    : Offline

O- ring.

Hi Joe,

I buy a box of mixed O-rings from a motor factors for about ten pounds which has every size and thickness of O-ring you could need.

doujoy

----------------------

Fri 27 May 2016 @ 21:31 Edit this messageQuote this messagePMQuote this message
Anon
Deleted
Posts :
Location :
Status    : Offline

I need the nut that screws down to hold the gearstick lever in the gearbox the one I have the gear lever just pushes in to it the new box needs the nut
Sun 29 May 2016 @ 20:17 Edit this messageQuote this messagePMQuote this message
Time in GMT
[Post Reply]
New posts since your last visit Administrative Functions: Open/Close/Delete Thread / Move Thread
Old post

Forum Jump:

Back to the CF-UK Homepage ][ Email CF-UK

Powered by FunkBoard vCF0.74c